1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
|
% Computer Modern Math Symbols 8 point invisible
if unknown cmbase: input cmbase fi
% RmS 91/10/27: corrected font identifier
font_identifier:="ICMSY"; font_size 8pt#;
u#:=17/36pt#; % unit width
width_adj#:=0pt#; % width adjustment for certain characters
serif_fit#:=0pt#; % extra sidebar near lowercase serifs
cap_serif_fit#:=4.1/36pt#; % extra sidebar near uppercase serifs
letter_fit#:=0pt#; % extra space added to all sidebars
body_height#:=216/36pt#; % height of tallest characters
asc_height#:=200/36pt#; % height of lowercase ascenders
cap_height#:=196.8/36pt#; % height of caps
fig_height#:=185.6/36pt#; % height of numerals
x_height#:=124/36pt#; % height of lowercase without ascenders
math_axis#:=72/36pt#; % axis of symmetry for math symbols
bar_height#:=69.6/36pt#; % height of crossbar in lowercase e
comma_depth#:=56/36pt#; % depth of comma below baseline
desc_depth#:=56/36pt#; % depth of lowercase descenders
crisp#:=8/36pt#; % diameter of serif corners
tiny#:=8/36pt#; % diameter of rounded corners
fine#:=7/36pt#; % diameter of sharply rounded corners
thin_join#:=7/36pt#; % width of extrafine details
hair#:=9/36pt#; % lowercase hairline breadth
stem#:=21.5/36pt#; % lowercase stem breadth
curve#:=25/36pt#; % lowercase curve breadth
ess#:=23/36pt#; % breadth in middle of lowercase s
flare#:=26.5/36pt#; % diameter of bulbs or breadth of terminals
dot_size#:=32/36pt#; % diameter of dots
cap_hair#:=9.5/36pt#; % uppercase hairline breadth
cap_stem#:=25.5/36pt#; % uppercase stem breadth
cap_curve#:=29/36pt#; % uppercase curve breadth
cap_ess#:=26/36pt#; % breadth in middle of uppercase s
rule_thickness#:=.36pt#; % thickness of lines in math symbols
dish#:=1/36pt#; % amount erased at top or bottom of serifs
bracket#:=16/36pt#; % vertical distance from serif base to tangent
jut#:=24/36pt#; % protrusion of lowercase serifs
cap_jut#:=29/36pt#; % protrusion of uppercase serifs
beak_jut#:=8.4/36pt#; % horizontal protrusion of beak serifs
beak#:=56/36pt#; % vertical protrusion of beak serifs
vair#:=8/36pt#; % vertical diameter of hairlines
notch_cut#:=8pt#; % maximum breadth above or below notches
bar#:=9.5/36pt#; % lowercase bar thickness
slab#:=9.5/36pt#; % serif and arm thickness
cap_bar#:=9.5/36pt#; % uppercase bar thickness
cap_band#:=9.5/36pt#; % uppercase thickness above/below lobes
cap_notch_cut#:=8pt#; % max breadth above/below uppercase notches
serif_drop#:=3.2/36pt#; % vertical drop of sloped serifs
stem_corr#:=1/36pt#; % for small refinements of stem breadth
vair_corr#:=1/36pt#; % for small refinements of hairline height
apex_corr#:=0pt#; % extra width at diagonal junctions
o#:=6/36pt#; % amount of overshoot for curves
apex_o#:=6/36pt#; % amount of overshoot for diagonal junctions
slant:=.25; % tilt ratio $(\Delta x/\Delta y)$
fudge:=1; % factor applied to weights of heavy characters
math_spread:=.4; % extra openness of math symbols
superness:=1/sqrt2; % parameter for superellipses
superpull:=1/6; % extra openness inside bowls
beak_darkness:=11/30; % fraction of triangle inside beak serifs
ligs:=2; % level of ligatures to be included
square_dots:=false; % should dots be square?
hefty:=false; % should we try hard not to be overweight?
serifs:=true; % should serifs and bulbs be attached?
monospace:=false; % should all characters have the same width?
variant_g:=true; % should an italic-style g be used?
low_asterisk:=false; % should the asterisk be centered at the axis?
math_fitting:=true; % should math-mode spacing be used?
% the following font parameters are explained in {\sl The \TeX book}, Appendix G
subs:=6/8; % subscripts to 8pt will normally be in 6pt type
rth#:=.4pt#; % assume that rules will come from cmex10
fontdimen 8: % parameters $\sigma_8$ through $\sigma_{22}$ will now be listed
math_axis#+3.51rth#+36/36pt#+subs*desc_depth#, % num1
math_axis#+1.51rth#+24/36pt#, % num2
math_axis#+1.51rth#+38/36pt#, % num3
-(math_axis#-3.51rth#-subs*fig_height#-98/36pt#), % denom1
-(math_axis#-1.51rth#-subs*fig_height#-24/36pt#), % denom2
7.49pt#-subs*asc_height#, % sup1
6.99pt#-subs*asc_height#, % sup2
82/36pt#, % sup3
36/36pt#, % sub1
72/36pt#, % sub2
subs*asc_height#-36/36pt#, % sup\_drop
18/36pt#, % sub\_drop
11.9pt#, % delim1
9.1pt#, % delim2
math_axis#; % axis\_height
extra_endchar := extra_endchar & "clearit;";
generate mathsy % switch to the driver file
|
