1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
|
% Computer Modern Astro Symbols 6 point (wmo)
if unknown cmbase: input cmbase fi
font_identifier:="CMASTRO"; font_size 6pt#;
u#:=14/36pt#; % unit width
width_adj#:=0pt#; % width adjustment for certain characters
serif_fit#:=0pt#; % extra sidebar near lowercase serifs
cap_serif_fit#:=2.8/36pt#; % extra sidebar near uppercase serifs
letter_fit#:=6/36pt#; % extra space added to all sidebars
body_height#:=162/36pt#; % height of tallest characters
asc_height#:=150/36pt#; % height of lowercase ascenders
cap_height#:=147.6/36pt#; % height of caps
fig_height#:=139.2/36pt#; % height of numerals
x_height#:=93/36pt#; % height of lowercase without ascenders
math_axis#:=54/36pt#; % axis of symmetry for math symbols
bar_height#:=52.2/36pt#; % height of crossbar in lowercase e
comma_depth#:=42/36pt#; % depth of comma below baseline
desc_depth#:=42/36pt#; % depth of lowercase descenders
crisp#:=6.5/36pt#; % diameter of serif corners
tiny#:=6.5/36pt#; % diameter of rounded corners
fine#:=6/36pt#; % diameter of sharply rounded corners
thin_join#:=6/36pt#; % width of extrafine details
hair#:=8/36pt#; % lowercase hairline breadth
stem#:=17.5/36pt#; % lowercase stem breadth
curve#:=20/36pt#; % lowercase curve breadth
ess#:=17/36pt#; % breadth in middle of lowercase s
flare#:=20.5/36pt#; % diameter of bulbs or breadth of terminals
dot_size#:=26/36pt#; % diameter of dots
cap_hair#:=8.5/36pt#; % uppercase hairline breadth
cap_stem#:=21/36pt#; % uppercase stem breadth
cap_curve#:=23.5/36pt#; % uppercase curve breadth
cap_ess#:=18.5/36pt#; % breadth in middle of uppercase s
rule_thickness#:=.31pt#; % thickness of lines in math symbols
dish#:=.8/36pt#; % amount erased at top or bottom of serifs
bracket#:=12/36pt#; % vertical distance from serif base to tangent
jut#:=19/36pt#; % protrusion of lowercase serifs
cap_jut#:=23/36pt#; % protrusion of uppercase serifs
beak_jut#:=6.8/36pt#; % horizontal protrusion of beak serifs
beak#:=42/36pt#; % vertical protrusion of beak serifs
vair#:=7/36pt#; % vertical diameter of hairlines
notch_cut#:=6pt#; % maximum breadth above or below notches
bar#:=8.5/36pt#; % lowercase bar thickness
slab#:=8.5/36pt#; % serif and arm thickness
cap_bar#:=8.5/36pt#; % uppercase bar thickness
cap_band#:=8.5/36pt#; % uppercase thickness above/below lobes
cap_notch_cut#:=6pt#; % max breadth above/below uppercase notches
serif_drop#:=2.4/36pt#; % vertical drop of sloped serifs
stem_corr#:=.8/36pt#; % for small refinements of stem breadth
vair_corr#:=.7/36pt#; % for small refinements of hairline height
apex_corr#:=0pt#; % extra width at diagonal junctions
o#:=4.5/36pt#; % amount of overshoot for curves
apex_o#:=4.5/36pt#; % amount of overshoot for diagonal junctions
slant:=.25; % tilt ratio $(\Delta x/\Delta y)$
fudge:=1; % factor applied to weights of heavy characters
math_spread:=.8; % extra openness of math symbols
superness:=1/sqrt2; % parameter for superellipses
superpull:=1/6; % extra openness inside bowls
beak_darkness:=11/30; % fraction of triangle inside beak serifs
ligs:=2; % level of ligatures to be included
square_dots:=false; % should dots be square?
hefty:=false; % should we try hard not to be overweight?
serifs:=true; % should serifs and bulbs be attached?
monospace:=false; % should all characters have the same width?
variant_g:=true; % should an italic-style g be used?
low_asterisk:=false; % should the asterisk be centered at the axis?
math_fitting:=true; % should math-mode spacing be used?
% the following font parameters are explained in {\sl The \TeX book}, Appendix G
subs:=5/6; % subscripts to 6pt will normally be in 5pt type
rth#:=.4pt#; % assume that rules will come from cmex10
fontdimen 8: % parameters $\sigma_8$ through $\sigma_{22}$ will now be listed
math_axis#+3.51rth#+36/36pt#+subs*desc_depth#, % num1
math_axis#+1.51rth#+9/36pt#, % num2
math_axis#+1.51rth#+29/36pt#, % num3
-(math_axis#-3.51rth#-subs*fig_height#-74/36pt#), % denom1
-(math_axis#-1.51rth#-subs*fig_height#-9/36pt#), % denom2
6.49pt#-subs*asc_height#, % sup1
5.99pt#-subs*asc_height#, % sup2
62/36pt#, % sup3
36/36pt#, % sub1
72/36pt#, % sub2
subs*asc_height#-36/36pt#, % sup\_drop
18/36pt#, % sub\_drop
11.9pt#, % delim1
8.1pt#, % delim2
math_axis#; % axis\_height
generate symbols % switch to the driver file
|
