1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
|
Doublestroke Font V1.111 27th of August, 2002
------------------------
This font is based on the Computer Modern Roman family of fonts
by D. E. Knuth. It is useful for typesetting the mathematical
symbols for the natural numbers (N), whole numbers (Z),
rational numbers (Q), real numbers (R) and complex numbers (C).
License
-------
You may use and distribute these fonts as you like.
You may modify these fonts as long as you do not
rename the files to one of those names that
Donald E. Knuth chose for the Computer Modern fonts.
(And seriously, who would want to do that?)
How to Install
--------------
1. If a previous version of this font is installed, remove all
the files, especially the font files that were generated by
Metafont after the first installation.
2. Depending on how you obtained this package it might be
necessary to unpack/uncompress an archive. Now the files
dsdoc.dvi dsrom12.pfb dsss10.mf dsss8.tfm
dsdoc.ps dsrom12.tfm dsss10.pfb dstroke.map
dsdoc.tex dsrom8.mf dsss10.tfm readme
dsfont.sty dsrom8.pfb dsss12.mf Udsrom.fd
dsrom10.mf dsrom8.tfm dsss12.pfb Udsss.fd
dsrom10.pfb dsrom.mf dsss12.tfm
dsrom10.tfm dsromo.mf dsss8.mf
dsrom12.mf dsromu.mf dsss8.pfb
should be present.
3. Make sure you have TeX, LaTeX (with NFSS), and Metafont
installed. Make sure that cmbase.mf is accessible by Metafont.
4. Move the files to their destination.
The files are and are needed by
*.tfm TeX font metric files TeX
*.fd font defintions TeX
*.sty style files TeX
*.mf Metafont sources Metafont
The exact location where the files belong depends on your
installation. As a first approximation, install them
near other files with the same extension.
5. Verify the installation by generating the documentation.
Run `latex dsdoc' and have a look at the file dsdoc.dvi which
contains the documentation and usage samples.
6. If you want to use the PostScript fonts, you have to make
them known to dvips and/or PDFTeX. The details of
this process depend on your system installation,
typically using the mapping information from the
file dstroke.map and following further instructions
contained in the main manual.
7. After reading the examples in the file dsdoc you can
use the fonts in your own documents.
After the Installation
----------------------
Do not worry, most installations complete without any problems.
However, if the procedure described above does not work, I suggest
the following actions:
- If LaTeX complains about a missing input file, check whether
the files *.fd and *.sty are accessible and readable.
- If LaTeX complains about a missing font, check the
placement of the files *.tfm .
- If LaTeX issues strange errors, you might have an old version
of LaTeX or NFSS. Try using the fonts with low-level font
commands instead of dsfont.sty and check the next item, too.
- If LaTeX issues strange errors, the files might have been
corrupted during transmission. Conversions of CR, LF, and
so on might cause this problem.
- If the previewer or the printer driver complains about missing
fonts and does not automatically call Metafont to generate
these font, either adapt your installation or generate
the fonts by hand. Depending on your installation you
must run something like
mf '\mode=localfont; input dsrom10'
for each of the fonts.
- If Metafont is called and complains about missing source
files, check whether these (*.mf) are placed correctly.
- If Metafont is called and complains about strange paths
or about paths that do not intersect, you are probably
generating the font at a lower resolution than 100 dpi.
There is little you can do except ignoring the errors or
telling Metafont to do so. Please report such errors only
if they occur at resolutions above 100 dpi.
- If the previewer or the printer driver complains about missing
characters, check whether you have deleted all files from
previous versions of this font.
- If the previewer or the printer driver complains about a
checksum error, check whether you have deleted all files from
previous versions of this font.
If that does not help and your friendly TeXnician is unavailable,
drop me a mail. I will try to help you, if time permits.
I am always glad to hear about improvements and bug reports,
general comments are appreciated, too.
Olaf Kummer
Universitaet Hamburg
Fachbereich Informatik -- Arbeitsbereich TGI
Vogt-Koelln-Strasse 30
22527 Hamburg (Germany)
mailto:kummer@informatik.uni-hamburg.de
http://www.informatik.uni-hamburg.de/TGI/mitarbeiter/wimis/kummer.html
|
