diff options
Diffstat (limited to 'Build/source/libs/cairo/cairo-1.14.0/INSTALL')
| -rw-r--r-- | Build/source/libs/cairo/cairo-1.14.0/INSTALL | 184 |
1 files changed, 184 insertions, 0 deletions
diff --git a/Build/source/libs/cairo/cairo-1.14.0/INSTALL b/Build/source/libs/cairo/cairo-1.14.0/INSTALL new file mode 100644 index 00000000000..9db68dee2ba --- /dev/null +++ b/Build/source/libs/cairo/cairo-1.14.0/INSTALL @@ -0,0 +1,184 @@ +Quick-start build instructions +------------------------------ +1) Configure the package: + + ./configure + +2) Compile it: + + make + +3) Install it: + + make install + +This final step may require temporary root access (eg. with sudo) if +you don't have write permission to the directory in which cairo will +be installed. + +NOTE: If you are working with source from git/cvs rather than from a tar +file, then you should use ./autogen.sh in place of ./configure +anywhere it is mentioned in these instructions. + +More detailed build instructions +-------------------------------- +1) Configure the package + + The first step in building cairo is to configure the package by + running the configure script. [Note: if you don't have a configure + script, skip down below to the Extremely detailed build + instructions.] + + The configure script attempts to automatically detect as much as + possible about your system. So, you should primarily just accept + its defaults by running: + + ./configure + + The configure script does accept a large number of options for + fine-tuning its behavior. See "./configure --help" for a complete + list. The most commonly used options are discussed here. + + --prefix=PREFIX + + This option specifies the directory under which the software + should be installed. By default configure will choose a + directory such as /usr/local. If you would like to install + cairo to some other location, pass the director to configure + with the --prefix option. For example: + + ./configure --prefix=/opt/cairo + + would install cairo into the /opt/cairo directory. You could + also choose a prefix directory within your home directory if + you don't have write access to any system-wide directory. + + After installing into a custom prefix, you will need to set + some environment variables to allow the software to be + found. Assuming the /opt/cairo prefix and assuming you are + using the bash shell, the following environment variables + should be set: + + PKG_CONFIG_PATH=/opt/cairo/lib/pkgconfig + LD_LIBRARY_PATH=/opt/cairo/lib + export PKG_CONFIG_PATH LD_LIBRARY_PATH + + (NOTE: On Mac OS X, at least, use DYLD_LIBRARY_PATH in place + of LD_LIBRARY_PATH above.) + + --enable-XYZ + --enable-XYZ=yes + --enable-XYZ=auto + --enable-XYZ=no + --disable-XYZ + + Cairo's various font and surface backends and other features can be + enabled or disabled at configure time. Features can be divided into + three categories based on their default state: + + * default=yes: These are the recommended features like PNG functions + and PS/PDF/SVG backends. It is highly recommended to not disable + these features but if that's really what one wants, they can be + disabled using --disable-XYZ. + + * default=auto: These are the "native" features, that is, they are + platform specific, like the Xlib surface backend. You probably + want one or two of these. They will be automatically enabled if + all their required facilities are available. Or you can use + --enable-XYZ or --disable-XYZ to make your desire clear, and then + cairo errs during configure if your intention cannot be followed. + + * default=no: These are the "experimental" features, and hence by + default off. Use --enabled-XYZ to enable them. + + The list of all features and their default state can be seen in the + output of ./configure --help. + +2) Compile the package: + + This step is very simple. Just: + + make + + The Makefiles included with cairo are designed to work on as many + different systems as possible. + + When cairo is compiled, you can also run some automated tests of + cairo with: + + make check + + NOTE: Some versions of X servers will cause the -xlib tests to + report failures in make check even when cairo is working just + fine. If you see failures in nothing but -xlib tests, please + examine the corresponding -xlib-out.png images and compare them to + the -ref.png reference images (the -xlib-diff.png images might also + be useful). If the results seem "close enough" please do not report + a bug against cairo as the "failures" you are seeing are just due + to subtle variations in X server implementations. + +3) Install the package: + + The final step is to install the package with: + + make install + + If you are installing to a system-wide location you may need to + temporarily acquire root access in order to perform this + operation. A good way to do this is to use the sudo program: + + sudo make install + +Extremely detailed build instructions +------------------------------------- +So you want to build cairo but it didn't come with a configure +script. This is probably because you have checked out the latest +in-development code via git. If you need to be on the bleeding edge, +(for example, because you're wanting to develop some aspect of cairo +itself), then you're in the right place and should read on. + +However, if you don't need such a bleeding-edge version of cairo, then +you might prefer to start by building the latest stable cairo release: + + http://cairographics.org/releases + +or perhaps the latest (unstable) development snapshot: + + http://cairographics.org/snapshots + +There you'll find nicely packaged tar files that include a configure +script so you can go back the the simpler instructions above. + +But you're still reading, so you're someone that loves to +learn. Excellent! We hope you'll learn enough to make some excellent +contributions to cairo. Since you're not using a packaged tar file, +you're going to need some additional tools beyond just a C compiler in +order to compile cairo. Specifically, you need the following utilities: + + automake + autoconf + autoheader + aclocal + libtoolize + pkg-config [at least version 0.16] + gtk-doc (recommended) + +Hopefully your platform of choice has packages readily available so +that you can easily install things with your system's package +management tool, (such as "apt-get install automake" on Debian or "yum +install automake" on Fedora, etc.). Note that Mac OS X ships with +glibtoolize instead of libtoolize. + +Once you have all of those packages installed, the next step is to run +the autogen.sh script. That can be as simple as: + + ./autogen.sh + +But before you run that command, note that the autogen.sh script +accepts all the same arguments as the configure script, (and in fact, +will generate the configure script and run it with the arguments you +provide). So go back up to step (1) above and see what additional +arguments you might want to pass, (such as prefix). Then continue with +the instructions, simply using ./autogen.sh in place of ./configure. + +Happy hacking! |