rm unswthesis, no license info

git-svn-id: svn://tug.org/texlive/trunk@49913 c570f23f-e606-0410-a88d-b1316a301751

3 files changed, 0 insertions, 468 deletions

diff --git a/Master/texmf-dist/doc/latex/unswthesis/README b/Master/texmf-dist/doc/latex/unswthesis/README
deleted file mode 100644
index 1f98ab2cb0f..00000000000
--- a/Master/texmf-dist/doc/latex/unswthesis/README
+++ /dev/null
@@ -1,29 +0,0 @@
-This directory contains the UNSW Thesis class.  The following files are
-supplied:
-
-unswthesis.cls          - The actual thesis class.  Some comments on its use
-                          appear in the file itself.
-fancyheadings.sty	- Required package by "unswthesis.cls".
-
-testunsw.tex            - Test out some of the UNSW Thesis class.  Requires
-                          the above two files.
-thesis.tex              - A severly trimmed-down version of my thesis, to
-                          show how *I* used the class.  Learning is often
-                          best done by example...
-mythesis.sty            - Required by "thesis.tex".  Shows how some useful
-                          things may be defined in LaTeX-2e.
-fancybox.sty            - Required by "thesis.tex" for fancy boxes.
-
-Note that these files are supplied AS IS, without any guarantee as to their
-suitability or even complience with university regulations.  Also, I cannot
-guarantee that I will support these files, nor provide any help for you to
-use them.
-
-I am interested in receiving feedback about these files; please contact me on
-John Zaitseff <J.Zaitseff@unsw.edu.au>.
-
-For anyone thinking of using LaTeX-2e seriously for their thesis, etc, I
-highly recommend the two books "LaTeX: A document preparation system",
-by Leslie Lamport, original author of LaTeX (2nd ed, published by
-Addison Wesley), and "The LaTeX Companion", by Goossens, Mittelbach
-and Samarin, (Addison Wesley).
diff --git a/Master/texmf-dist/doc/latex/unswthesis/testunsw.tex b/Master/texmf-dist/doc/latex/unswthesis/testunsw.tex
deleted file mode 100644
index f3a45a88805..00000000000
--- a/Master/texmf-dist/doc/latex/unswthesis/testunsw.tex
+++ /dev/null
@@ -1,100 +0,0 @@
-% This is a sample thesis, showing how to use the "unswthesis" class.
-% (C) John Zaitseff, 1995. <J.Zaitseff@unsw.edu.au>
-
-\documentclass{unswthesis}
-%\documentclass[singlespacing]{unswthesis}
-
-\thesisuni{The University of New South Wales}
-\thesisschool{School of Electrical Engineering and\\
-               Computer Engineering}
-
-\thesistitle{Building the \'Elan Am386SC300 Microcomputer}
-\thesisauthor{John Zaitseff (2120715)}
-\thesisdegree{Bachelor of Engineering (Computer Engineering)}
-\thesisdate{October 1995}
-
-\thesissupervisor{A/Prof.\ Branko Celler}
-\thesisassessor{Dr.\ Tim Hesketh}
-
-\begin{document}
-
-% Apart from the abstract, none of the front matter is double-spaced.
-
-\frontmatter
-\maketitle
-
-\begin{abstract}
-The abstract document appears before any front matter.  As can be seen, it
-is doubled-spaced in the final document.  Theses \emph{shouldn't} have to be
-doubled-spaced, should they?  As you can see, it makes them awful!
-
-A second paragraph for the abstract --- not a very useful one. Again shows
-the double-spacing of the environment.
-\end{abstract}
-
-\tableofcontents
-\listoffigures
-\listoftables
-
-% Apart from footnotes, tables and figures, all of the main matter is
-% double-spaced (unless the "singlespace" option was passed to
-% \documentclass).
-
-\mainmatter
-
-\chapter{Introduction}
-
-The main matter is double-spaced, as can be seen. A few lines of ``junk''
-will confirm this:
-
-The quick brown fox jumped over the lazy dog.  The quick brown fox jumped
-over the lazy dog.  The quick brown fox jumped over the lazy dog.  The quick
-brown fox jumped over the lazy dog%
-%
-\footnote{A famous line; the quick brown fox really \emph{did} jump over the
-lazy dog. You can see that footnotes are \emph{not} double-spaced.}%
-%
-.
-The quick brown fox jumped over the lazy dog.  The quick brown fox jumped
-over the lazy dog.  The quick brown fox jumped over the lazy dog.
-%
-\begin{itemize}
-    \item The quick brown fox jumped over the lazy dog.  The quick brown fox
-	  jumped over the lazy dog.  The quick brown fox jumped over the
-	  lazy dog.
-    \item The quick brown fox jumped over the lazy dog.  The quick brown fox
-	  jumped over the lazy dog.  The quick brown fox jumped over the
-	  lazy dog.
-    \item The quick brown fox jumped over the lazy dog.  The quick brown fox
-	  jumped over the lazy dog.  The quick brown fox jumped over the
-	  lazy dog.
-\end{itemize}
-
-The quick brown fox jumped over the lazy dog.  The quick brown fox jumped
-over the lazy dog.  The quick brown fox jumped over the lazy dog.
-
-Tables and figures are \emph{not} double-spaced. See, for example,
-Figure~\ref{fg:sample}.
-%
-\begin{figure}
-%
-The quick brown fox jumped over the lazy dog.  The quick brown fox jumped
-over the lazy dog.  The quick brown fox jumped over the lazy dog. The quick
-brown fox jumped over the lazy dog.  The quick brown fox jumped over the
-lazy dog.  The quick brown fox jumped over the lazy dog. The quick brown fox
-jumped over the lazy dog.  The quick brown fox jumped over the lazy dog.
-The quick brown fox jumped over the lazy dog.
-%
-\caption{A sample figure}\label{fg:sample}
-\end{figure}
-
-The quick brown fox jumped over the lazy dog.  The quick brown fox jumped
-over the lazy dog.  The quick brown fox jumped over the lazy dog.  The quick
-brown fox jumped over the lazy dog.  The quick brown fox jumped over the
-lazy dog.  The quick brown fox jumped over the lazy dog.  The quick brown
-fox jumped over the lazy dog.  The quick brown fox jumped over the lazy dog.
-The quick brown fox jumped over the lazy dog.  The quick brown fox jumped
-over the lazy dog.  The quick brown fox jumped over the lazy dog.  The quick
-brown fox jumped over the lazy dog.
-
-\end{document}
diff --git a/Master/texmf-dist/doc/latex/unswthesis/thesis.tex b/Master/texmf-dist/doc/latex/unswthesis/thesis.tex
deleted file mode 100644
index a7cd80c10c2..00000000000
--- a/Master/texmf-dist/doc/latex/unswthesis/thesis.tex
+++ /dev/null
@@ -1,339 +0,0 @@
-%%% [ This file is provided for the purpose of being an example of using
-%%%   the "unswthesis" class.  As such, any information relating to the
-%%%   thesis itself has been removed. ]
-
-%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
-%                                                                       %
-%                      University of New South Wales                    %
-%               School of Computer Science and Engineering              %
-%                                 Thesis                                %
-%                                                                       %
-%                        (C) John Zaitseff, 1995.                       %
-%                                                                       %
-%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
-
-% Author:       John Zaitseff <J.Zaitseff@unsw.edu.au>
-% Date:         October, 1995. [ Stripped 28/8/96 ]
-% Format:       LaTeX-2e
-
-%     This document contains the Undergraduate Thesis for John Zaitseff,
-% completed at the University of New South Wales in Session 2, 1995.
-
-%@@@ introduces places where something needs to be done.
-
-%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
-\documentclass[final]{unswthesis}
-\usepackage{mythesis}
-
-%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
-\begin{document}
-\frontmatter
-
-\maketitle
-\tableofcontents
-\listoffigures
-\listoftables
-
-\mainmatter
-
-%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
-\chapter{Introduction}\label{ch:intro}
-
-One of the fastest growing areas of computing today is the area of
-portable, often hand-held, devices.  These highly-integrated computers
-are used in increasingly many areas, especially as Personal Digital
-Assistants, including hand-held data loggers, bar code scanners and meter
-readers.
-
-This thesis describes the design of one such portable system, based on
-the \Elan microprocessor.  This system features the use of the current
-state-of-the-art technology, including high-density surface-mounted
-components, low battery power consumption, and directly integrated
-support for the new \PCMCIA standard.
-
-%%%%%%%%%%%%%%%%%%%%%%%%%%%
-\section*{Acknowledgements}
-
-%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
-\chapter{Applications}\label{ch:apps}
-
-\section{Biomedical applications}
-
-Such a set-up would look something like Figure~\ref{fg:aging}.
-%
-\begin{ourfigure}
-%\includegraphics{homemon.ps}
-includegraphics...
-\caption{Remote monitoring of health status in the home}\label{fg:aging}
-\end{ourfigure}
-
-The r\^ole of the \EPC, the system this thesis describes, in such
-biomedical systems would be to actually take the place of the hand-held
-device taking data readings, or as part of the instrumentation modules
-placed around the house.  The requirements of the \EPC in such systems
-are described in the next chapter.
-
-%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
-\chapter{Alternatives}\label{ch:alt}
-
-In Chapter~\ref{ch:apps}, we saw a number of applications in which a
-portable computer may be used.
-
-...
-
-The \Elan CPU chooses the configuration mode at reset time, on the rising
-edge of \pnob{RESIN}, by sampling the state of three pins: \pnob{DTR},
-\pnob{RTS} and \pn{SOUT}.  These pins are usually used for serial port
-output, except for their special function at reset.  To select one of the
-modes, we place \res{10}{k} pull-up or pull-down resistors on these pins,
-as per Table~\ref{tb:elmode}.  In this table, a ``1'' indicates pull-up,
-``0'' indicates pull-down, and ``X'' indicates that no resistor is
-required.
-%
-\begin{ourtable}
-\begin{tabular}{|c|c|c|l|}
-\hline
-\multicolumn{3}{|c|}{Pin state at reset}  &  \\
-\cline{1-3}
-\rule[1.3ex]{0mm}{1.3ex}\pnob{DTR} & \pnob{RTS} & \pn{SOUT} &
-	\multicolumn{1}{|c|}{\raisebox{1.5ex}[0cm][0cm]{Mode Selected}} \\
-\hline
-0  &  0  &  X  &  Internal CGA \\
-1  &  0  &  0  &  Local bus, 1 \by clock \\
-1  &  0  &  1  &  Local bus, 2 \by clock \\
-X  &  1  &  X  &  Maximum ISA \\
-\hline
-\end{tabular}\par
-\begin{tabular}{c@{\,}c@{\,}l}
-0 &=& pull-down resistor (to \pn{GND}) \\
-1 &=& pull-up resistor (to \pn{VCC5}) \\
-X &=& no resistor \\
-\end{tabular}
-\caption{Selection of the \Elan operating mode}\label{tb:elmode}
-\end{ourtable}
-
-%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
-\subsection{Level 1 ISA Bus Support}\label{sc:el:isa1}
-
-Table~\ref{tb:elisa1} shows the meaning of the
-pins used in this mode.
-%
-\begin{ourtable}
-\renewcommand{\thefootnote}{\textit{\alph{footnote}}}
-\begin{tabular}{|l|c|l|}
-\hline
-Pin Name		& Type%
-%
-\footnote{I~=~Input, O~=~Output, I/O~=~Bidirectional.  These are with
-	  respect to the \Elan device itself.}
-%
-				& Function \\
-\hline
-\pn{AEN}		& O	& DMA address enable (DMA cycle)\\
-\pn{TC}			& O	& DMA terminal count\\
-\pn{SYSCLK}		& O	& System clock%
-				\footnote{ISA bus timing is \emph{not}
-				derived from this signal: it is meant to
-				be used for the keyboard controller
-				only.}\\
-\pn{PIRQ1}		& I	& Programmable interrupt request~1\\
-\pn{DRQ2}		& I	& DMA channel 2 request\\
-\pn{X1OUT} / \pn{BAUDOUT}
-			& O	& Video clock or serial port clock\\
-
-\pnob{MCS16}		& I	& Memory device is \bit{16}%
-\footnote{Note that \pnob{MCS16}, \pnob{IOCS16}, \pnob{SBHE} and
-	      \pn{IRQ14} are \emph{not} available in dual-scan LCD mode.} \\
-\pnob{IOCS16}		& I	& I/O device is \bit{16}\footnotemark[3]\\
-\pnob{SBHE}		& O	& Byte high enable\footnotemark[3]\\
-\pn{IRQ14}		& I	& Interrupt request~14\footnotemark[3]\\
-\hline
-\end{tabular}
-\renewcommand{\thefootnote}{\textrm{\arabic{footnote}}}
-\caption{ISA bus support, common subset}\label{tb:elisa1}
-\end{ourtable}
-
-Before we continue, a few points to note about the notation:
-%
-\begin{itemize}
-    \item  A pin name like \pn{PIN} indicates either an
-	   \emph{active-high} pin (i.e., where the pin is asserted when
-	   it is at a \High level, generally either \threevolt or
-	   \fivevolt), or a \emph{rising-edge} pin (i.e., where the pin
-	   is asserted on the rising edge, from \Low to \High, of a
-	   pulse).
-    \item  A name like \pnob{PIN} is the opposite: it indicates an
-	   \emph{active-low} pin, or one that is asserted on the
-	   \emph{falling-edge} (\High to \Low) of a signal.
-    \item  A name like \pnm{PIN}{3}{0} is \emph{shorthand} for pins
-	   individually named \pn{PIN0}, \pn{PIN1}, \pn{PIN2} and
-	   \pn{PIN3}.
-    \item  All pins are with reference to the microprocessor, i.e.,
-	   ``Output'' means output \emph{from} the processor to external
-	   peripherals.
-\end{itemize}
-
-The following is a description of the pins listed in
-Table~\ref{tb:elisa1}.  Much of this information is from pages 39 to~49
-of the \book{Data Book}~\cite{ci:data}, although some critical
-information is not listed in \emph{any} part of the supplied
-documentation:
-%
-\begin{pindescr}
-    \iopin {\pnm{SA}{23}{0}}%
-	   {System address bus}%
-	   {output, active high}
-
-		The system address bus outputs the physical memory or I/O
-		address.  It is used by all external devices, except
-		system DRAM\@.  In local bus mode, this represents the CPU
-		local address, except that \pn{SA0} is not used.  Note
-		that pins \pnm{SA}{23}{13} are multiplexed with the
-		memory bus; see section~\ref{sc:el:mem} for more details.
-
-    \iopin {\pnm{D}{15}{0}}%
-	   {System data bus}%
-	   {bidirectional, active high}
-
-		The system data bus inputs data during memory or I/O read
-		cycles, and outputs data during memory and I/O write
-		cycles.  In local bus mode, as well as in DRAM read/write
-		mode, this bus is used to represent the CPU data bus.
-\end{pindescr}
-
-...
-
-These modes are summarised in
-Table~\ref{tb:pmmodes}; see also pages~9--15 of the \book{Data
-Book}~\cite{ci:data}.
-%
-\begin{ourtable}
-\begin{tabular}{|p{0.15\linewidth}|p{0.6\linewidth}|}
-\hline
-Mode		&Description\\
-\hline\hline
-Full speed	&All clocks are at fastest speed and all peripherals are
-		powered up.\\\hline
-Low speed	&CPU clock is reduced to a lower speed; all other clocks
-		are at full speed.\\\hline
-Doze		&CPU, system and DMA clocks, as well as the high-speed
-		phase-locked loop, are stopped.\\\hline
-Sleep		&Additional clocks and peripherals are stopped (depending
-		on the programmed settings), as is the serial port
-		controller (UART).\\\hline
-Suspend		&A special BIOS routine is invoked to save the system
-		state, then virtually all of the system is powered down.
-		The phase-locked loops are turned off.\\\hline
-Off		&A powered-down mode in which \pn{PGP2} and \pn{PGP3} are
-		set to a predefined state.  Memory refresh is still
-		active.  No activity can cause the processor to leave
-		this state, except for a power-on reset.\\
-\hline
-\end{tabular}
-\caption{Power Management Unit operating modes}\label{tb:pmmodes}
-\end{ourtable}
-
-%%%%%%%%%%%%%%%%%%%%%%%%%%
-\subsection{Other Remarks}
-
-One of the additional features of the internal video controller is that
-it may be programmed to appear in the I/O location for a CGA controller
-(\addr{3D4}--\addr{3DA}) or in the I/O location for a Hercules Graphics
-Adapter (\addr{3B4}--\addr{3BF}).
-
-%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
-\chapter{Conclusions}\label{ch:concl}
-
-In conclusion, this project has been \emph{very} challenging, but very
-interesting as well.  Although we were not able to proceed with the
-implementation, we are more than reasonably satisfied that the design is
-sound and thorough.  If the project is continued in the next year, the
-\EPC will eventually emerge as a symbol of today's modern computing.
-
-
-%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
-\begin{thebibliography}{199}
-\ssp
-
-%%%%%%%%%%%%%%%%%%%%%
-\bibitem{ci:poqetpad}
-
-``\book{Development of a Range of \PCMCIA Type III Instrumentation Modules for
-Clinical Measurement, based on the PoqetPad Plus Pen-based Computer}'',
-Branko Celler, Biomedical Systems Laboratory, University of NSW,
-Australia, 23rd June 1993.
-
-%%%%%%%%%%%%%%%%%
-\bibitem{ci:data}
-
-``\book{\Elan \AmSC Microprocessor Data Sheet}'',
-Mobile Computing Products Division of Advanced Micro Devices, Inc.
-
-%%%%%%%%%%%%%%%%
-\bibitem{ci:prm}
-
-``\book{\Elan \AmSC Microprocessor Programmers' Reference Manual}'',
-Mobile Computing Products Division of Advanced Micro Devices, Inc.
-
-%%%%%%%%%%%%%%%%%%%%
-\bibitem{ci:intlist}
-
-``\book{PC Interrupt List}''
-Ralf Brown, Release~47, August 1995.
-Available as\linebreak\texttt{ftp://ftp.cs.cmu.edu/afs/cs.cmu.edu/user/ralf/pub/inter47*.zip}
-
-
-%%%%%%%%%%%%%%%%%%%
-\bibitem{ci:pcspec}
-
-``\book{\PCMCIA Standards}'',
-``\book{PC Card Standard 2.1}'',
-``\book{Socket Services Specification 2.1}'',
-``\book{Card Services Specification 2.1}'',
-``\book{PC Card ATA Specification 1.02}'',
-``\book{AIMS Specification 1.01}'',
-``\book{Recommended Extensions 1.0}'',
-Personal Computer Memory Card International Association,
-July 1993.
-
-\end{thebibliography}
-
-%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
-\appendix
-\ssp
-\chapter{\Elan Computer Schematics}\label{ch:schem}
-
-The following pages show the final \EPC schematics.  The actual
-schematics are in the following order:
-%
-\begin{enumerate}
-    \item System Block Diagram
-    \item \Elan Microprocessor
-    \item Miscellaneous
-    \item System Memory
-    \item Display Interface
-    \item \PCMCIA Buffers
-    \item \PCMCIA Connectors
-    \item Parallel Port
-    \item Serial Port
-    \item Keyboard Connector
-    \item Expansion Connector
-    \item DC/DC Power
-    \item Power Switching
-\end{enumerate}
-%
-% Leave enough space (13 pages) for the schematics.
-\clearpage
-\addtocounter{page}{13}
-
-%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
-\chapter{Component Data Sheets}\label{ch:datasheet}
-
-The following pages contain all of the data sheets for the components
-used in the \EPC design, except for the \Elan \AmSC itself (about
-300~pages, available seperately as~\cite{ci:data, ci:prm}, and simple
-components like resistors, capacitors and diodes.
-
-...
-
-\end{document}